Factory direct sales Mutex-high-quality pure water-based repair wooden furniture putty
Direct sales Mutex-high-quality pure water-based repair wood furniture manufacturers
One: Performance introduction:
VADERWALD Mutex-environmentally friendly water-based putty is a pure water-based environmentally friendly product, type A is ~ water-based nano-color-fillable polymer network fiber (powder), curing agent type B is ~ pure water-based polymer expansion type Crosslinking agent (liquid), both of which are pure water, no VOCS, no organic solvents, no toxic and hazardous substances, odorless, green and environmentally friendly; flame retardant, flame retardant grade B1, high temperature resistance of 380 degrees , The curing reaction caused by the mixing of AB agent is a cross-linking cross self-crystallization reaction; it does not generate any heat and gas outflow, so it can be filled in place for the filling thickness (depth) within ten centimeters at one time, without multiple repetitions Repeat (thin squeegee) squeegee. After drying, it does not affect the adhesion of the coating. The repairing and color absorption ability on wood is 3-5 times that of oily putty, and the hardness after drying can reach 6 H. It has room temperature curing, fast drying speed, easy to apply and scratch, not easy to peel, not easy to change color, not easy to sink, not easy to peel off, not easy to crack, not easy to shrink, good extensibility, strong air permeability, easy to polish, strong adhesion, It has a series of advantages such as simple construction, smooth surface to be coated, firm adhesion to the substrate, and good thermal conductivity to electrical performance. At room temperature, VADERWALD Mutex-environmentally friendly water-based putty AB agent can dry within 10-20 minutes after mixing (30-40 minutes in winter), and stacking can be carried out without heating and drying, saving procedures and shortening process time. It is suitable for repairing scars, lack of materials, pits and larger-sized cracks on wooden floors, large boards, furniture.
Two: How to use:
1: Put the VADERWALD Mutex-environmentally friendly water-based putty A type and curing agent B type according to 3:1～4:1 (by weight). The default color of the AB agent is the original wood color (oak color), if you need to color it Choose (water-based color paste or water-based color concentrate, red, yellow, black) to adjust the desired color (stir fully to keep the color consistent) and mix evenly. This product is suitable for current use. Once the AB agent is mixed in proportion, it must be used up within the curing reaction time (generally the curing reaction time of putty ranges from 5 minutes to 15 minutes). The lower the temperature, the slower the curing reaction. The higher the lower, the faster the curing reaction. For example, when using assembly line operation, once the AB agent is mixed, please keep it in a stirring state (active state). This method can effectively delay the curing reaction time.
2: VADERWALD Mutex-environmentally friendly water-based putty summer recommends the ratio of A agent: B agent 3:1 as a reference for the ratio, spring and autumn recommends the ratio of A agent: B agent 3.5:1 as a reference, and winter recommends A agent ：The ratio of B agent 4:1 is used as a reference. Users can also adjust the proportion of AB agent according to the actual operation requirements and adjust the proportion of AB agent according to the actual operation requirements. It is recommended to adjust the concentration of water-based putty to agent A: agent B 4:1 to ensure that it is filled in place at one time. When the cavities and cracks are small, it is recommended to adjust the concentration of water-based putty to agent A: agent B 3:1 , To ensure that the mixed putty reaches self-leveling and fully penetrates into the wood void.
3: During operation, it is recommended to use a spatula to scrape the mixed putty (remember that the AB agent is prepared for current use, how much to use to avoid waste) on the surface of the board that needs to be filled, if a thick layer is required Scrape can be filled in place at one time, or it can be thinly scraped to the required thickness in multiple times. If air bubbles infiltrate during coating, it must be wiped thoroughly with a scraper to ensure good adhesion. Generally, the surface is dry 10-20 minutes after scraping the dust (if you need to polish and spray paint, it is recommended to dry for 12 hours in summer, and after 24 hours in winter, you can polish it and remove the dust on the surface before proceeding with the subsequent process of painting and spraying).